Tutorial Cara Setting Konfigrasi OSPF di Cisco Packet Tracer - Wanjay

Tutorial Cara Setting Konfigrasi OSPF di Cisco Packet Tracer

    Kali ini admin akan membahas Tutorial tentang KONFIGURASI OSPF DENGAN CISCO PACKET TRACER. Oke langsung saja ke topik pembahasan.

    Pertama kita buat dulu sebuah jaringan , seperti gambar dibawah.....
    Tutorial Cara Setting Konfigrasi OSPF di Cisco Packet Tracer
    Selanjutnya..
    berikan IP Address pada setiap PC.. 

    1. PC 1 dengan nama "PC0"..

    Tutorial Cara Setting Konfigrasi OSPF di Cisco Packet Tracer

    2. PC 2 dengan nama "PC 2"..

    Tutorial Cara Setting Konfigrasi OSPF di Cisco Packet Tracer

    3. PC 3 dengan nama "PC 3"..

    Tutorial Cara Setting Konfigrasi OSPF di Cisco Packet Tracer

    Tahap selanjutnya berikan IP Address pada setiap router . Contoh sebagai berikut : 

    Pemberian IP Address di Router 1

    --- System Configuration Dialog ---

    Continue with configuration dialog? [yes/no]: no

    Press RETURN to get started!

    Router>enable
    Router#configure terminal
    Enter configuration commands, one per line. End with CNTL/Z.
    Router(config)#int fa0/0
    Router(config-if)#ip add 172.18.8.1 255.255.0.0
    Router(config-if)#no shut

    Router(config-if)#
    %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

    %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

    Router(config-if)#exit
    Router(config)#int se2/0
    Router(config-if)#ip add 192.168.8.1 255.255.255.0
    Router(config-if)#band 125
    Router(config-if)#cl ra 125000
    Router(config-if)#no shut

    %LINK-5-CHANGED: Interface Serial2/0, changed state to down
    Router(config-if)#exit

    Konfigurasi EIGRP pada Router 1,

    Router(config)#router ospf 4
    Router(config)#router-id 2.2.2.2
    Router(config-router)#net 172.18.8.0 0.0.255.255 area 0 
    Router(config-router)#net 192.168.8.0 0.0.0.255 area 0
    Router(config-router)#log-adjacency
    Router(config-router)#end
    Router#
    %SYS-5-CONFIG_I: Configured from console by console
    wr
    Building configuration...
    [OK]
    Router#

    Pemberian IP Address di Router 2 

    --- System Configuration Dialog ---

    Continue with configuration dialog? [yes/no]: no

    Press RETURN to get started!

    Router>enable
    Router#configure terminal
    Enter configuration commands, one per line. End with CNTL/Z.
    Router(config)#int fa0/0
    Router(config-if)#ip add 172.19.9.1 255.255.0.0
    Router(config-if)#no shut

    Router(config-if)#
    %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

    %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

    Router(config-if)#exit
    Router(config)#int se2/0
    Router(config-if)#ip add 192.168.8.2 255.255.255.0
    Router(config-if)#band 125
    Router(config-if)#no shut

    %LINK-5-CHANGED: Interface Serial2/0, changed state to down
    Router(config-if)#exit 

    Router(config-if)#exit
    Router(config)#int se3/0
    Router(config-if)#ip add 18.8.8.1 255.0.0.0
    Router(config-if)#band 125
    Router(config-if)#cl ra 125000
    Router(config-if)#no shut

    %LINK-5-CHANGED: Interface Serial3/0, changed state to down
    Router(config-if)#exit 

    Konfigurasi OSPF pada Router 2,

    Router(config)#router ospf 4
    Router(config-router)#net 172.19.9.1 0.0.255.255 area 0
    Router(config-router)#net 192.168.8.0 0.0.0.255 area 0
    Router(config-router)#net 18.8.8.0 0.255.255.255 area 1
    Router(config-router)#log-adjacency
    Router(config-router)#end
    Router#
    %SYS-5-CONFIG_I: Configured from console by console
    wr
    Building configuration...
    [OK]
    Router#

    Pemberian IP Address di Router 3

    --- System Configuration Dialog ---

    Continue with configuration dialog? [yes/no]: no

    Press RETURN to get started!

    Router>enable
    Router#configure terminal
    Enter configuration commands, one per line. End with CNTL/Z.
    Router(config)#int fa0/0
    Router(config-if)#ip add 172.16.10.1 255.255.0.0
    Router(config-if)#no shut

    Router(config-if)#
    %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

    %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

    Router(config-if)#exit
    Router(config)#int se2/0
    Router(config-if)#ip add 18.8.8.2 255.0.0.0
    Router(config-if)#band 125
    Router(config-if)#no shut

    %LINK-5-CHANGED: Interface Serial2/0, changed state to down
    Router(config-if)#exit

    Konfigurasi OSPF pada Router 3,

    Router(config)#router ospf 4
    Router(config)#router-id 4.4.4.4
    Router(config-router)#net 172.16.10.0 0.0.255.255 area 1
    Router(config-router)#net 18.8.8.0 0.255.255.255 area 1
    Router(config-router)#log-adjacency
    Router(config-router)#end
    Router#
    %SYS-5-CONFIG_I: Configured from console by console
    wr
    Building configuration...
    [OK]
    Router#

    Setelah dikonfigurasi, coba di ping antara PC0 , PC1 dan PC2..

    SELAMAT MENCOBA................

    Apabila kurang jelas bisa di tanyakan.................

    Subscribe Wanjay Untuk Mendapatkan Notifikasi Artikel Terbaru Lainnya dan Agar tidak Ketinggalan Update, Gratis!!!

    Caranya Masukkan Alamat Email Kamu > Muncul Pop Up > Centang Saya Bukan Robot > Complete > Lalu Buka Email Kamu Pilih Pesan Activate your Email Subscription, Untuk Aktifkan Notifikasi Lalu Buka Link Aktivasinya > Selesai dan Terima Kasih sudah Subscribe :)

    Buka Komentar

    Iklan Atas Artikel

    Iklan Tengah Artikel 1

    Iklan Tengah Artikel 2

    Iklan Bawah Artikel